Location:
Search - CAN s3c24
Search list
Description:
Platform: |
Size: 215040 |
Author: |
Hits:
Description: 实现了ucos在s3c2440上的移植，内含lwip在ucos上的实现（非本人移植），lwip并未加在系统里，可分别看待-UCOS achieved in the transplant S3C2440 containing lwIP in uCOS realize on the (non-I transplantation), lwip not added to the system, can be viewed
Platform: |
Size: 2266112 |
Author: 赵明飞 |
Hits:
Description: sjf2410的使用,可以烧写nandfash 和nor flash-sjf2410 use, you can nandfash and nor flash programmer
Platform: |
Size: 340992 |
Author: 汪晓伟 |
Hits:
Description: arm 博创2410的 vivi源码，可以进行配置，编译-2410 Fiberxon arm of the vivi-source, you can configure, compile
Platform: |
Size: 240640 |
Author: jensenhaw |
Hits:
Description: 本驱动程序在s3c2440上实现了两路基于SPI的CAN总线控制器。两通道可以并行，并使用外部定义的两个信号量来通知接收任务收到CAN总线帧，并将其存入预先定义的队列中（帧定义在CAN总线控制器驱动程序的头文件中）。CAN总线控制器的中断引脚分别连接到ARM的EINT3和EINT8_23上-The driver s3c2440 achieved a two-way SPI-based CAN bus controller. Two channels can be parallel, and use the external definition of two semaphore to inform the takeover, received CAN bus frame, and store pre-defined queue (frame defined in the CAN bus controller driver header file ). CAN-bus controller interrupt pin is connected to the ARM-EINT3 and EINT8_23 on
Platform: |
Size: 10240 |
Author: 胡奔 |
Hits:
Description: S3C2440A下彩色液晶显示系统的设计,以三星公司的嵌入式微处理器S3C2440A和夏普公司3.5inLCD屏LQ035Q7DH01为基础,设计了显示硬件电路,介绍了帧缓冲设备的处理机制及底层驱动的接口函数,针对本显示系统给出了如何开发其Linux帧缓冲设备驱动程序。不论是显示硬件电路还是软件驱动程序,都有很强的可移植性,可以方便地移植到不同的平台。-S3C2440A under the color LCD display system designed to Samsung' s S3C2440A Embedded Microprocessor and Sharp 3.5inLCD screen LQ035Q7DH01 based on the design of display hardware circuit, introduced a frame buffer device handling mechanism and the low-level driver interface functions for The display system shows how to develop the Linux frame buffer device driver. Both the display hardware circuitry or software drivers, there is a strong portability, can be easily ported to different platforms.
Platform: |
Size: 270336 |
Author: cen |
Hits:
Description: 专为S3C2440开发的简易bootloader源代码包，适用于启动Linux，通过supervivi烧写到Nand Flash的Block 0,
可以自适应启动64M/128M-1G Nand Flash
-S3C2440 development for the simple bootloader source code package for start Linux, by supervivi programmed to Nand Flash in the Block 0, can be adaptive start 64M/128M-1G Nand Flash
Platform: |
Size: 14336 |
Author: 林伟山 |
Hits: